Forces · Cambridge syllabus 1.5.1 · Lesson 3 of 5
Springs and Elasticity
Includes Supplement objectivesExtension is stretched length minus original length. Up to the limit of proportionality, extension is proportional to load and the spring constant is k = F ÷ x. A larger spring constant means a stiffer spring. Beyond the limit of proportionality, the straight-line relationship no longer applies.
By the end, you can
- Define extension.
- Investigate the relationship between force and extension.
- Understand proportional behaviour.
- Identify the limit of proportionality. [Supplement]
- Sketch, plot and interpret load–extension graphs.
- Define the spring constant as force per unit extension and use k = F ÷ x. [Supplement]
Extension
Extension is how much longer a spring has become: the stretched length minus the original, unstretched length. It is not the total length, and confusing the two is the single most common error in this topic. A spring 12 cm long unloaded and 17 cm long under a load has an extension of 5 cm, not 17 cm.
To measure it, hang the spring from a clamp, record the position of the pointer with no load, then add masses in equal steps and record the position each time. Subtract the no-load reading from each to get the extension for each load. Take the readings at eye level against a fixed ruler, or parallax will add a consistent error to every one.
The load on the spring is the weight of the masses hanging from it, so convert each mass to a force in newtons before plotting, using W = mg with g = 9.8 N/kg. A 100 g mass is 0.100 kg, so its weight is 0.100 × 9.8 = 0.98 N; 200 g gives 1.96 N, 300 g gives 2.94 N, and so on.
Worth remembering
- Extension = stretched length − original length.
- Load = weight of the masses: 100 g weighs 0.100 × 9.8 = 0.98 N.
- Add the load in equal steps and read the pointer at eye level each time.
Proportional behaviour
Plot a load–extension graph, with the load in newtons up the side and the extension in centimetres or metres along the bottom. For a spring, the early part of the graph is a straight line through the origin. That is the useful result: extension is proportional to load, so doubling the load doubles the extension. To sketch it, draw a straight line from the origin; when plotting real results, draw the best straight line through the points and look for any that do not fit.
The straight line does not continue for ever. Beyond a point called the limit of proportionality the graph starts to curve, and the extension is no longer proportional to the load. On a graph it is the last point of the straight section, where the line begins to bend away. A spring loaded past this point extends by more than the straight line predicts for each extra newton.
The spring constant k is the force per unit extension: k = F ÷ x, where F is the load and x the extension it produces. It is the gradient of the straight part of the load–extension graph, and it describes stiffness: a large k means a stiff spring that extends little for a given force. A spring that extends 4.0 cm under a load of 2.0 N has k = 2.0 ÷ 4.0 = 0.50 N/cm. In metres the extension is 0.040 m, so k = 2.0 ÷ 0.040 = 50 N/m. Both units are correct; just keep the one you choose consistent through the calculation.
- k = F ÷ x
- The spring constant is the force needed for each unit of extension.k in N/m or N/cm, F in N, x in m or cm
Worth remembering
- Up to the limit of proportionality, extension is proportional to load: a straight line through the origin.
- Beyond the limit of proportionality the load–extension graph curves.
- k = F ÷ x, in N/m or N/cm; it is the gradient of the straight section. Larger k = stiffer.
Worked example
A 20 N/m spring extends 0.15 m: force = 20 × 0.15 = 3 N.
Investigate scatter and systematic error
Change a value and watch the readings follow. Open it on the lab stage
Investigate scatter and systematic error
There is no zero offset, and the readings lie up to 0.484 cm from the best-fit line.
- Furthest point from the best-fit line
- 0.484 cm
- 3.13 cm − 2.646 cm at 1 s
- Best-fit intercept
- 1.165 cm
- 1 cm true + 0 cm offset + 0.165 cm random
- Best-fit gradient
- 1.965 cm/s
- (20.815 cm − 1.165 cm) ÷ 10 s
Goal
Find out how random scatter and a zero offset each change a set of readings, and which of them taking more repeats can fix.
Predict, where you are
If Ithe, thewill
Say what you expect before you move anything. Check makes the change for you.
Test, still to come
Change one thing at a time and watch the readings. The notebook keeps a reading each time you record one.
Explain, still to come
After you check a prediction, this says why it happened.
Try this · 0 of 3
- Turn the random scatter up to 1.5 cm with no zero offset. Does the best-fit line still follow the true line?, not yet
- Set a zero offset of −1 cm with no scatter. How far does every reading move?, not yet
- With 1 cm of scatter and a 1 cm zero offset, take 10 repeats at each time. Which error does averaging reduce, and which does it leave?, not yet
reading = true value + zero offset + random error
at 5 s: 11 cm + 0 cm − 0.229 cm = 10.771 cm
Investigation notebook · 0 readings
Change one variable at a time and record the results. These readings stay here until you leave this lesson or reset the notebook.
About this model
Made-up readings of a distance that truly grows as 2 cm/s × time + 1 cm. Each reading’s random error comes from a fixed set drawn once, up to the scatter either side, so the same settings always give the same readings. The best-fit line is the least-squares straight line through the plotted points.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
4 cm = 0.04 m. k = 2 ÷ 0.04 = 50 N/m.
Check your method, units and explanation against it.
Marked practice
Set 1 of 4 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.