Measurement · Lesson 1 of 2
Measurement Quality
Choose an instrument with suitable range and precision. Read scales square on at eye level, to the nearest half of the smallest division, and check zero before use. Precision describes how finely a scale reads or how closely repeated readings agree; accuracy describes closeness to the true value.
By the end, you can
- Choose suitable instruments.
- Record measurements with sensible precision.
- Recognise zero errors and parallax.
- Read a scale to the nearest half of its smallest division.
Accuracy and precision
A good measurement starts with the right instrument. It needs a suitable range, so that the quantity fits on its scale, and a scale fine enough for the job. A 10 cm³ measuring cylinder measures 6.5 cm³ of liquid far better than a 250 cm³ one, whose marks are too far apart; a 0–5 N newton meter suits a small force better than a 0–50 N one; light gates time a fast trolley better than a hand-held stopwatch.
Record each reading to the precision of the instrument: the smallest difference its scale can reliably show, sometimes called its resolution. A length read from a millimetre scale is written to the nearest millimetre, as 4.0 cm or 40 mm and not 4 cm, because the final zero records that the reading really was taken to that precision; writing 4.000 cm would claim more than the ruler can show. A digital stopwatch shows hundredths of a second, but a hand-timed reading is affected by reaction time of around 0.1–0.3 s, so the last digit should not be trusted.
Two faults spoil many readings. A zero error is when an instrument shows a reading when it should show zero, such as a balance reading 0.3 g with nothing on it, or a newton meter whose pointer rests at 0.2 N. Check before you start, reset it to zero if you can, and otherwise subtract the zero reading from every measurement. A parallax error happens when a scale is read from an angle, so a pointer or liquid level appears against the wrong mark. Avoid it by putting your eye level with the reading and looking square on to the scale; read a measuring cylinder at the bottom of the meniscus.
Read a scale to the nearest half of its smallest division. When a pointer, a liquid level or the end of an object lies between two marks, judge whether it is nearer one of the marks or nearer halfway between them, and record that value. On a thermometer marked every 1 °C, a liquid thread ending midway between 23 °C and 24 °C is recorded as 23.5 °C; one ending level with the 23 °C mark is recorded as 23.0 °C. Judging a position between marks like this is called interpolating between scale divisions.
Worth remembering
- Choose an instrument with a suitable range and a scale fine enough for the job.
- Record readings to the precision of the instrument: 4.0 cm on a millimetre scale, not 4 cm.
- Check for zero error before starting, and read scales square on at eye level to avoid parallax.
- Read a scale to the nearest half of its smallest division, interpolating between the marks.
Worked example
A ruler with 1 mm divisions cannot justify a reported length of 12.34567 cm; a thermometer thread halfway between 23 °C and 24 °C reads 23.5 °C.
Read the scale
Change a value and watch the readings follow. Open it on the lab stage
Read the scale
Eye level: the line of sight meets the scale where the object ends, at 7.8 cm.
- Apparent reading
- 7.8 cm
- 7.8 cm + 0 cm
- Measured length
- 6.6 cm
- 7.8 cm − 1.2 cm
- Reading error
- 0 cm
- 7.8 cm − 7.8 cm
Goal
Measure an object that does not start at zero, and find out what looking at the scale from an angle does to the reading.
Predict, where you are
If Ithe, thewill
Say what you expect before you move anything. Check makes the change for you.
Test, still to come
Change one thing at a time and watch the readings. The notebook keeps a reading each time you record one.
Explain, still to come
After you check a prediction, this says why it happened.
Try this · 0 of 2
- Line the object up with the 2 cm mark and measure it at eye level: subtract the start reading from the end reading., not yet
- Move your eye until the reading is at least 0.2 cm too high., not yet
- Convert the measured length to metres, then check your answer in the equation under the stage.
length = end reading − start reading
7.8 cm − 1.2 cm = 6.6 cm = 0.066 m
Investigation notebook · 0 readings
Change one variable at a time and record the results. These readings stay here until you leave this lesson or reset the notebook.
About this model
The object sits 0.4 cm above the scale, which exaggerates parallax. Its left end is lined up with the start mark by eye, straight on, so only the end is read at the viewing angle. A positive angle puts the eye to the left.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
A non-zero initial reading would shift every measurement by a systematic offset.
Check your method, units and explanation against it.
Marked practice
Set 1 of 4 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.