Electromagnetic Effects · Cambridge syllabus 4.5 · Lesson 5 of 6
Generators
Includes Supplement objectivesA coil rotating in a magnetic field has its sides cutting the field lines, first one way and then the other, so an alternating e.m.f. is induced. Slip rings maintain connections without switching the coil terminals. Mechanical work supplies the electrical energy generated.
By the end, you can
- Convert mechanical energy into electrical energy.
- Explain alternating output. [Supplement]
- Describe basic AC generation. [Supplement]
- Describe the use of slip rings and brushes in an a.c. generator. [Supplement]
- Sketch and interpret graphs of e.m.f. against time, relating the position of the coil to the peaks, troughs and zeros. [Supplement]
Generator principle
A generator uses electromagnetic induction to transfer energy from mechanical work into electrical energy. Something must turn it: a turbine driven by steam, wind or falling water in a power station, a bicycle wheel, or a hand crank. It does not make energy from nothing. The more current it supplies, the harder it is to turn, and a little of the energy is wasted heating its wires and as sound.
A simple alternating-current generator is a coil rotated in a magnetic field. As it turns, its sides cut across the field lines, and an e.m.f. is induced. Each side moves up through the field for half a turn and down through it for the next half, so the e.m.f. reverses every half turn and the output is alternating. A generator can instead keep the coil still and rotate a magnet inside it, as a bicycle dynamo does; the field through the coil keeps reversing, so its e.m.f. alternates too.
With a rotating coil, wires joined straight to it would twist round the axle, so the connections are made through slip rings: two complete rings, one joined to each end of the coil, turning with it. A fixed carbon brush presses on each ring and slides on it, carrying the current to the external circuit. Because each ring is always joined to the same end of the coil, the connections never swap, so the alternating e.m.f. reaches the circuit as it is generated. A d.c. motor has a split-ring commutator instead, and that is the one structural difference between the two.
The e.m.f. depends on how fast the sides of the coil cut field lines, and that depends on the coil’s position. When the plane of the coil is at right angles to the field, its sides move along the field lines, cutting none, so the e.m.f. is zero. A quarter turn later the plane of the coil is parallel to the field and its sides cut straight across the lines as fast as possible, so the e.m.f. is at a peak. After another quarter turn it is zero again, and after three-quarters of a turn the coil is parallel to the field once more with its sides swapped, giving a trough, a peak in the opposite direction. The graph of e.m.f. against time is a smooth wave: zero, peak, zero, trough and back to zero for every turn.
Turning the coil faster makes its sides cut the field lines faster, so the peaks get taller, and makes more turns each second, so the cycles crowd closer together on the graph and the frequency rises. A stronger magnet or more turns on the coil make the peaks taller without changing the frequency.
Worth remembering
- A generator transfers energy from mechanical work into electrical energy.
- Slip rings and brushes connect the spinning coil without swapping, so the output stays a.c.
- Zero e.m.f. when the coil’s plane is at right angles to the field; a peak or trough when parallel.
- Faster turning gives taller peaks and a higher frequency.
Worked example
Doubling rotation rate increases frequency; in the ideal model it also increases peak EMF.
Generate an alternating output
Part of the full Physics course. This unit’s free simulation is Build a circuit.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
Mechanical energy is transferred to electrical energy, with some energy dissipated as heating and sound.
Check your method, units and explanation against it.
Marked practice
Set 1 of 4 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.