Physical Quantities and Measurement Techniques · Cambridge syllabus 1.1 · Lesson 2 of 4
Measuring Length, Area and Volume
Align the object with a known ruler mark and subtract the initial reading from the final reading. Look perpendicular to the scale to avoid parallax. For a cylinder of liquid, read the bottom of the meniscus at eye level.
By the end, you can
- Use rulers and measuring instruments correctly.
- Read scales with appropriate precision.
- Avoid parallax when taking readings.
- Find an average value for a small distance by measuring many together and dividing.
- Calculate volume of regular solids from dimensions.
- Determine volume of irregular objects using displacement.
- Convert between common units of volume: cm³, dm³ and m³.
Length
A ruler does not measure length; it measures the difference between two positions. That distinction matters because the end of a ruler is often worn or has a margin before the zero mark. The reliable method is to line the object up against a clear mark — 1.0 cm, say — read the position of the other end, and subtract. A block running from 1.2 cm to 7.8 cm is 6.6 cm long, and the worn end never entered the calculation.
Read to the precision the instrument actually offers, and no further. A millimetre ruler lets you record 6.6 cm honestly; writing 6.6432 cm claims a precision the ruler does not have.
The last source of error is your eye. If you look at the scale from an angle, the mark you read is not the mark the object lines up with, and the reading is wrong by a consistent amount — this is parallax. Look perpendicular to the scale, straight down at the mark. For a liquid in a measuring cylinder the surface curves; read the bottom of that curve, the meniscus, with your eye level with it.
Some things are too small to measure well one at a time. A sheet of paper is about 0.1 mm thick, which is less than the smallest division on a ruler. The answer is to measure many of them together and divide. A stack of 100 sheets measures 1.2 cm, so one sheet is 1.2 ÷ 100 = 0.012 cm, or 0.12 mm. The same trick finds the diameter of a thin wire: wind 20 turns tightly side by side around a pencil, measure the width of the coil, say 1.6 cm, and divide by 20 to get 0.08 cm. The reading error is still about 1 mm, but it is now shared between all the sheets or turns, so the error in one of them is tiny.
Worth remembering
- Length = final reading − initial reading. Do not trust the worn end of a ruler.
- Read perpendicular to the scale to avoid parallax; read a liquid at the bottom of the meniscus.
- Record only the precision the instrument provides.
- Small distance: measure many together, then divide by how many there are.
Volume
For a shape with straight edges, volume comes from the dimensions. A cuboid is length × width × height; a cylinder is πr²h, the area of the circular face multiplied by how far it extends. Measure each dimension separately with a ruler, and keep the units the same throughout — mixing centimetres and millimetres in one multiplication is a common and expensive slip.
An irregular object has no formula, so you measure the space it takes up instead. Part-fill a measuring cylinder with water and record the reading. Lower the object in until it is fully submerged, and record the new reading. The object has pushed the water up by exactly its own volume, so the difference between the two readings is the volume. A stone that raises the water from 30 cm³ to 55 cm³ has a volume of 25 cm³. Tie it to a thread and lower it gently: dropping it splashes water out, and trapped air bubbles make the object seem larger than it is.
Volume is measured in cubic centimetres (cm³), cubic decimetres (dm³) or cubic metres (m³), and conversions between them trip people up because they involve three dimensions. A decimetre is 10 cm, so a cube 1 dm on each side holds 10 × 10 × 10 = 1000 cm³: 1 dm³ = 1000 cm³. Since 1 cm = 10⁻² m, a cubic centimetre is (10⁻²)³ = 10⁻⁶ m³, and so 1 dm³ = 1000 × 10⁻⁶ = 10⁻³ m³. Put the other way round, 1 m³ = 1000 dm³ = 1 000 000 cm³. A 2.5 dm³ bottle of water holds 2500 cm³, or 0.0025 m³.
Worth remembering
- Regular solid: cuboid = l × w × h; cylinder = πr²h.
- Irregular solid: volume = final water reading − initial water reading.
- 1 cm³ = 10⁻⁶ m³; 1000 cm³ = 1 dm³ = 10⁻³ m³.
Worked example
An object runs from 1.2 cm to 7.8 cm: length = 7.8 − 1.2 = 6.6 cm. Water rises from 40 to 58 cm³: object volume = 18 cm³.
Density and displacement
Change a value and watch the readings follow. Open it on the lab stage
Density and displacement
It sinks in water: the level rises from 100 cm³ to 140 cm³.
- Object density
- 3 g/cm³
- 120 g ÷ 40 cm³
- Liquid density
- 1 g/cm³
- Cylinder reading
- 140 cm³
- 100 cm³ + 40 cm³ displaced
- Rise in level
- 40 cm³
- 140 cm³ − 100 cm³
Goal
Measure an object’s volume by displacement, work out its density, and find what decides whether it floats.
Predict, where you are
If Ithe, thewill
Say what you expect before you move anything. Check makes the change for you.
Test, still to come
Change one thing at a time and watch the readings. The notebook keeps a reading each time you record one.
Explain, still to come
After you check a prediction, this says why it happened.
Try this · 0 of 3
- Keep the volume at 40 cm³ and double the mass. What happens to the density?, not yet
- Make a 50 cm³ object that neither floats nor sinks in water., not yet
- Find an object that floats in brine but sinks in oil., not yet
density = mass ÷ volume
120 g ÷ 40 cm³ = 3 g/cm³; water is 1 g/cm³
Investigation notebook · 0 readings
Change one variable at a time and record the results. These readings stay here until you leave this lesson or reset the notebook.
About this model
The cylinder holds 100 cm³ of liquid before the object goes in: oil of 0.8 g/cm³, water of 1 g/cm³ or brine of 1.2 g/cm³. An object denser than the liquid sinks; a less dense one floats with only part of it under the surface. The drawing is a flat slice, so the block’s area is drawn to the same scale as the cylinder’s.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
Volume = 24 cm³. Since 1 cm³ = 10⁻⁶ m³, volume = 2.4 × 10⁻⁵ m³.
Check your method, units and explanation against it.
Marked practice
Set 1 of 5 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.