Electrical Quantities · Cambridge syllabus 4.2 · Lesson 2 of 6
Current
Includes Supplement objectivesCurrent is rate of charge flow, I = Q/t. Conventional current is defined in the direction positive charge would move; in a metal electrons drift the opposite way. An ammeter is connected in series.
By the end, you can
- Know that electric current is related to the flow of charge.
- Define current as the charge passing a point per unit time and use I = Q ÷ t. [Supplement]
- Use analogue and digital ammeters with different ranges.
- Understand conventional current direction. [Supplement]
- Describe electrical conduction in metals in terms of the movement of free electrons.
- Know the difference between direct current (d.c.) and alternating current (a.c.).
Current
An electric current is a flow of charge. In a complete circuit the charges move round together, and the more charge that flows past a point, the larger the current. Current is measured in amperes, A, usually shortened to amps; small currents are given in milliamps, where 1 mA = 0.001 A.
More precisely, current is the charge passing a point per unit time: I = Q ÷ t, with charge in coulombs, time in seconds and current in amperes. One ampere is one coulomb per second. Rearranged, Q = It, so a current of 3 A flowing for 20 s transfers 60 C. The time must be in seconds: 2 A for 3 minutes transfers 2 × 180 = 360 C, not 6 C.
Current is measured with an ammeter, connected in series with the component so that the same current passes through both. An ammeter has a very low resistance, so putting it in does not change the current. An analogue ammeter has a needle moving over a scale: work out what one small division is worth, then read the needle from directly in front. A digital ammeter shows the value as a number. Many ammeters have several ranges, such as 0–200 mA, 0–2 A and 0–10 A. Choose the smallest range that the current will not go over, because it gives the most precise reading; on too small a range a digital meter shows an overload sign and an analogue needle goes off the end of the scale. Check the meter reads zero before you start.
Conventional current is defined as flowing from the positive terminal of the supply, round the circuit, to the negative terminal, and every circuit diagram and rule in the course uses that direction. The free electrons in a metal actually flow the opposite way, from negative to positive, because the convention was fixed before the electron was discovered. Use conventional current for everything unless a question specifically asks about electron flow.
- I = Q ÷ t
- Current is the charge passing a point per unit time.I in A, Q in C, t in s. Rearranged: Q = It.
Worth remembering
- Current is a flow of charge, measured in amperes (A).
- I = Q ÷ t, so 1 A is 1 C passing a point each second.
- An ammeter goes in series; choose the smallest range the current will not exceed.
- Conventional current flows from + to −; electrons flow from − to +.
Electrons, d.c. and a.c.
A metal is made of a fixed lattice of positive ions with some electrons free to move between them. With no cell connected, these free electrons wander at random in all directions, so there is no overall flow of charge. Connect the metal into a complete circuit with a cell and the free electrons all drift steadily in one direction, towards the positive terminal, while still jostling about. That drift of free electrons is the electric current in the metal.
Because a wire is already full of free electrons, they all start drifting together as soon as the circuit is complete, which is why a lamp lights the instant the switch closes. Break the circuit anywhere and the drift stops everywhere. The electrons are not used up by a lamp: as many leave it each second as enter it, and what the lamp takes from them is energy.
Current comes in two types. Direct current, d.c., flows in one direction only; it is what a cell or a battery supplies. Alternating current, a.c., keeps reversing its direction, flowing one way and then the other, over and over again; it is what the mains supply provides, going through 50 or 60 complete cycles every second depending on the country. On a graph of current against time, d.c. stays on one side of zero, often as a flat line, while a.c. swings above and below zero in a repeating wave.
Worth remembering
- In a metal, current is a drift of free electrons through the lattice of positive ions.
- Electrons are not used up: components take energy from them, not charge.
- d.c. flows in one direction only (cells, batteries); a.c. keeps reversing (the mains).
Worked example
A current of 0.4 A transfers 12 C in 30 s because Q = It.
Count flowing charge
Part of the full Physics course. This unit’s free simulation is Build a circuit.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
t = 180 s; Q = 2 × 180 = 360 C.
Check your method, units and explanation against it.
Marked practice
Set 1 of 5 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.