Electrical Quantities · Cambridge syllabus 4.2 · Lesson 4 of 6
Resistance and Ohm's Law
Includes Supplement objectivesResistance R = V/I. A resistor at constant temperature has a straight I–V graph through the origin. A filament lamp heats as current grows, increasing resistance; a diode conducts mainly in one direction.
By the end, you can
- Use resistance = potential difference / current.
- Understand the meaning of resistance.
- Describe an experiment to determine resistance using a voltmeter and an ammeter.
- Sketch and explain the current–voltage graphs for a resistor of constant resistance, a filament lamp and a diode. [Supplement]
- Explain why the resistance of a filament lamp rises as it gets hotter. [Supplement]
Resistance
Resistance measures how much a component opposes the flow of current: R = V ÷ I, with potential difference in volts, current in amperes and resistance in ohms, Ω. One ohm is one volt per ampere. This lesson’s title uses the name Ohm’s law, but the syllabus never uses that name: what you need is this equation and the current–voltage graphs in the next section.
Rearranged, V = IR and I = V ÷ R. A lamp with 12 V across it carrying 0.5 A has a resistance of 12 ÷ 0.5 = 24 Ω. A component with a higher resistance lets a smaller current through for the same p.d.
Physically, resistance arises because the drifting free electrons collide with the vibrating ions of the metal lattice, transferring energy to them. That energy appears as heating, which is why a resistor warms up and why a filament lamp glows.
To measure the resistance of a component, such as a resistor or a length of wire, connect it in series with a cell, a switch and an ammeter, and connect a voltmeter in parallel across the component alone. Close the switch, read both meters and calculate R = V ÷ I: readings of 3.0 V and 0.20 A give 3.0 ÷ 0.20 = 15 Ω. For a more reliable value, add a variable resistor in series to change the current, take several pairs of readings, calculate R for each and average them, and switch off between readings so the component does not heat up.
- R = V ÷ I
- Resistance is the potential difference across a component divided by the current through it.R in Ω, V in V, I in A. Rearranged: V = IR.
Worth remembering
- R = V ÷ I, in ohms. Also V = IR and I = V ÷ R.
- Resistance heats the component, because electrons transfer energy to the lattice.
- To measure R: ammeter in series, voltmeter in parallel across the component, then R = V ÷ I.
Current–voltage graphs
A graph of current against potential difference shows how a component’s resistance behaves. For a resistor of constant resistance, such as a fixed resistor kept at a steady temperature, the graph is a straight line through the origin: double the p.d. and the current doubles. Reverse the p.d. and the current reverses with the same size, so the line carries straight on through the origin into the opposite quarter of the graph.
A filament lamp’s graph starts out straight near the origin and then curves, getting flatter as the p.d. rises: each extra volt adds less current than the one before, so the resistance is increasing. The cause is temperature. As the current grows, the filament gets hotter, its metal ions vibrate more, and the free electrons collide with them more often, so it is harder for them to drift through and the resistance rises. The curve has the same shape for negative p.d.s, because a reversed current heats the filament just as much.
A diode lets current through in one direction only. In the forward direction its graph stays close to zero until the p.d. reaches a small value, roughly 0.7 V for a typical diode, and then rises steeply. In the reverse direction the current is practically zero, so the graph runs along the axis. In a circuit, a diode acts like a one-way valve for current.
At any point on a current–voltage graph, the resistance is V ÷ I worked out from the values at that point. On the straight line it is the same everywhere; on the lamp’s curve it grows as the p.d. increases.
Worth remembering
- Constant resistance: a straight line through the origin.
- Filament lamp: the curve flattens at higher p.d., because its resistance rises as it heats up.
- Diode: current flows in one direction only; almost none flows in reverse.
- Resistance at any point on the graph is V ÷ I at that point.
Worked example
A resistor at 6 V carrying 0.3 A has resistance 20 Ω.
Build a circuit
Free for everyone, on its own page.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
R = 12/0.5 = 24 Ω.
Check your method, units and explanation against it.
Marked practice
Set 1 of 4 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.