Electrical Quantities · Cambridge syllabus 4.2 · Lesson 5 of 6
Factors Affecting Resistance
Includes Supplement objectivesA longer wire has greater resistance; a thicker wire has lower resistance for the same material and temperature. Metals usually increase resistance when heated. An NTC thermistor decreases resistance with rising temperature; an LDR decreases resistance with brighter light.
By the end, you can
- Length: a longer wire has a greater resistance.
- Cross-sectional area: a thicker wire has a smaller resistance.
- Material: wires of the same size made of different metals have different resistances.
- Temperature: the resistance of a metal wire, such as a lamp filament, rises as it gets hotter. [Supplement]
- Use the facts that resistance is directly proportional to length and inversely proportional to cross-sectional area. [Supplement]
- Thermistors.
- Light-dependent resistors (LDRs).
- Explain how resistance changes with a physical condition.
Wire resistance
The resistance of a metal wire depends on four things, and questions usually ask you to change one and predict the effect.
Length: a longer wire has a greater resistance, because the electrons have further to travel through the lattice and make more collisions on the way.
Cross-sectional area: a thicker wire has a smaller resistance, because there is more room for the current, with more free electrons drifting side by side — it is the difference between a narrow pipe and a wide one.
For a metal wire at a steady temperature these relationships are exact. Resistance is directly proportional to length: double the length and the resistance doubles, so if 1.0 m of a wire has a resistance of 4.0 Ω, 2.5 m of the same wire has 10 Ω. Resistance is inversely proportional to cross-sectional area: double the area and the resistance halves. Doubling the diameter of a wire multiplies its area by four, so it divides the resistance by four.
Material: some metals conduct better than others. Copper has a low resistance for its size, which is why it is used for connecting wire; nichrome has a much higher resistance, which is why it is used in heating elements.
Temperature: for a metal, resistance rises with temperature, as the lattice ions vibrate more and impede the electrons. For a thermistor the opposite is true, which the next section uses.
Worth remembering
- A longer wire has more resistance; a thicker wire has less.
- Resistance is proportional to length and inversely proportional to cross-sectional area.
- Copper has a low resistance and nichrome a high one; for a metal, resistance rises with temperature.
Sensors
Two components are deliberately built to change their resistance with their surroundings, which makes them useful as sensors.
A thermistor has a resistance that falls as the temperature rises — the opposite of a metal wire. In a circuit, warming it lets more current through, so it can be used to switch on a fan, trigger a fire alarm or control a thermostat.
A light-dependent resistor, or LDR, has a resistance that falls as the light intensity rises. In the dark its resistance is very high, perhaps megohms; in bright light it drops to hundreds of ohms. That makes it the natural choice for switching street lighting on at dusk or for a camera’s light meter.
Both are usually used in a potential divider, so the change in resistance becomes a change in voltage that a circuit can act on. That arrangement is covered in the circuits topic.
Worth remembering
- Thermistor: resistance falls as temperature rises.
- LDR: resistance falls as light intensity rises.
- Both are normally used in a potential divider so the change appears as a voltage.
Worked example
Doubling a uniform wire’s length doubles its resistance if cross-sectional area and temperature stay unchanged.
Change a wire’s resistance
Part of the full Physics course. This unit’s free simulation is Build a circuit.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
It decreases.
Check your method, units and explanation against it.
Marked practice
Set 1 of 5 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.