Electric Circuits · Cambridge syllabus 4.3 · Lesson 1 of 5
Circuit Symbols and Diagrams
Includes Supplement objectivesCircuit diagrams show electrical connections using standard symbols. Straight connecting lines represent wires, not their physical route. An ammeter goes in series; a voltmeter goes across a component.
By the end, you can
- Cell
- Battery
- Switch
- Lamp
- Resistor
- Variable resistor
- Ammeter
- Voltmeter
- Diode [Supplement]
- Motor
- Heater, thermistor (NTC), light-dependent resistor (LDR) and fuse.
- Power supply (d.c. and a.c.), generator and potential divider.
- Magnetising coil, transformer, relay and electric bell.
- Light-emitting diode (LED). [Supplement]
Symbols
A circuit diagram is a standardised drawing, and the standard matters because it lets anyone read any circuit. Components are drawn as agreed symbols and joined by straight lines representing wires, with corners at right angles and no attempt to show what anything actually looks like.
A cell is two parallel lines across the wire: a long thin line for the positive terminal and a short thick one for the negative. A battery is two or more cells joined in a row, all facing the same way. A switch is a short line hinged at one contact, lifted away from the other contact when it is open. A lamp is a circle with a cross in it; a circle with a letter in it is an ammeter (A), a voltmeter (V) or a motor (M). Earth is a line ending in three short bars, each shorter than the last.
Several symbols are based on a rectangle. A plain rectangle is a fixed resistor. With an arrow drawn diagonally through it, it is a variable resistor, whose resistance can be changed to change the current, for example to dim a lamp. A rectangle divided into sections is a heater, a resistor designed to transfer energy by heating. A rectangle with a diagonal line through it that ends in a short flat foot is a thermistor: its resistance falls as it gets hotter. A rectangle with two arrows pointing in at it is a light-dependent resistor, whose resistance falls as the light on it gets brighter. A rectangle with a line running through it from end to end is a fuse, which melts and breaks the circuit if the current is too large.
A diode is a triangle pointing along the wire with a bar across its tip. It lets current through only in the direction the triangle points, and blocks it the other way.
Two conventions cause most of the lost marks. A junction where wires connect is drawn with a solid dot; wires that cross without connecting have no dot. And an ammeter is always drawn in the main line of the branch it measures, while a voltmeter is always drawn as a loop across the component it measures.
Worth remembering
- Use the standard symbols and straight lines; a diagram is not a picture.
- Circle with a cross: lamp. A, V or M in a circle: ammeter, voltmeter, motor.
- Rectangles: plain for a resistor, arrow through for variable, divided for a heater, line through for a fuse.
- A dot means a junction; crossing wires without a dot are not connected.
More components
Some circuits are driven by a power supply instead of a cell. Its symbol is a pair of small open circles, one on each lead, standing for its two terminals. A d.c. power supply has + and − marked beside its terminals and drives current in one direction; an a.c. power supply has a wavy line (~) between its terminals and drives a current that keeps reversing. A generator is drawn as a square with a G inside it, not a circle: it is a source of e.m.f. that has to be turned to work.
A potential divider is drawn as a resistor with an arrow pointing onto its side from a third lead. The arrow is a sliding contact: moving it along the resistor changes the p.d. between it and one end, from zero up to the whole supply p.d., which is how a volume control works.
Three symbols are built from coils. A magnetising coil is a row of loops, like a spring seen from the side; a current through it produces a magnetic field that can magnetise a steel bar inside it. A transformer is two coils side by side with two straight lines between them, standing for its iron core; it changes an alternating p.d. into a larger or a smaller one. A relay coil is a small rectangle with one lead going in at the top and the other leaving at the bottom; a current in it makes an electromagnet that works a separate switch, so a small current in one circuit can switch on a large current in another.
An electric bell is drawn as a dome sitting on a flat line, with its two leads coming down underneath. While a current flows through it, its electromagnet repeatedly pulls a hammer against the gong, and the bell rings. A light-emitting diode, or LED, is the diode symbol with two small arrows pointing away from it, for the light coming out. Like any diode it conducts in one direction only, and it gives out light when current flows through it that way.
Worth remembering
- Power supply: two open circles; d.c. marked + and −, a.c. with ~ between them. Generator: G in a square.
- Potential divider: a resistor with an arrow onto its side from a third lead.
- Magnetising coil: a row of loops. Transformer: two coils with two lines between. Relay coil: a small rectangle.
- Electric bell: a dome on a line. LED: a diode with two arrows pointing away; it lights one way only.
Worked example
A lamp and ammeter share the same series path. The voltmeter has a separate connection to each side of the lamp.
Build a circuit
Free for everyone, on its own page.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
In parallel, with its terminals connected to opposite sides of the resistor.
Check your method, units and explanation against it.
Marked practice
Set 1 of 6 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.