Electric Circuits · Cambridge syllabus 4.3 · Lesson 2 of 5
Series Circuits
Includes Supplement objectivesA series circuit has one path, so current is the same through each component. The source potential difference is shared between components. With fixed resistance, the larger resistor receives the larger share.
By the end, you can
- Current is the same at all points in a series circuit.
- The total potential difference across the components in a series circuit equals the sum of the individual potential differences. [Supplement]
- Construct and use series and parallel circuits.
- Calculate the combined e.m.f. of several sources in series.
Current
A series circuit has one single path, so every component is joined end to end in a loop. The immediate consequence is that the current is the same at every point in that loop.
It is worth being clear about why, because the intuition that current "gets used up" is common and wrong. Charge is conserved: electrons are not consumed by a lamp, they pass through it. Whatever flows into a component flows out of it. What the lamp takes is energy, not charge.
So an ammeter placed anywhere in a series circuit reads the same value. Adding more components in series increases the total resistance and therefore reduces that shared current, which is why two lamps in series are dimmer than one. And if any component fails or a switch opens, the single path is broken and everything stops — which is the main disadvantage of wiring in series.
Worth remembering
- One path, so the current is the same everywhere in a series circuit.
- Current is not used up: components take energy, not charge.
- A break anywhere stops everything.
Potential difference
In a series circuit, the total potential difference across the components equals the sum of the potential differences across each one: V = V₁ + V₂ + V₃. With a single source, that total is the source’s e.m.f. This is conservation of energy: each coulomb receives a fixed amount of energy from the source and gives all of it up as it passes through the components in turn.
The share each component takes is proportional to its resistance, since V = IR and the current is the same for all of them. A 6 V supply across a 2 Ω and a 4 Ω resistor in series drives a current of 6 ÷ 6 = 1 A, so the 2 Ω resistor takes 2 V and the 4 Ω resistor takes 4 V. The larger resistance takes the larger share.
Adding the readings is a quick check on any series circuit. With a 9.0 V battery, a lamp and a resistor in series, if a voltmeter across the lamp reads 5.5 V, a voltmeter across the resistor must read 9.0 − 5.5 = 3.5 V.
Worth remembering
- In series, the total p.d. is the sum of the individual p.d.s: V = V₁ + V₂ + …
- The larger resistance takes the larger share of the p.d.
- With one source, the p.d.s across the components add up to its e.m.f.
Building circuits
To build a series circuit, start at one terminal of the cell and join each component to the next, end to end, so that there is a single loop back to the other terminal; an ammeter can go anywhere in that loop. To build a parallel circuit, give each component its own branch between the same two junctions, so that each branch is connected directly across the supply. Follow the diagram one wire at a time, and before switching on, trace a complete path from one terminal of the source back to the other.
Using the circuits means measuring and comparing. Move an ammeter around a series circuit and its reading does not change; put it in each branch of a parallel circuit and the branch currents can differ, while the current from the source is larger than any of them. Unscrew one lamp in series and every lamp goes out; unscrew one in parallel and the others stay lit. Switch off before changing any connection.
Sources connected in series add their e.m.f.s, as long as they all face the same way, with the positive terminal of each joined to the negative terminal of the next. Three 1.5 V cells in series give 1.5 + 1.5 + 1.5 = 4.5 V. Turn one cell round and its e.m.f. subtracts instead: two cells one way and one reversed give 1.5 + 1.5 − 1.5 = 1.5 V. Different sources combine in the same way: a 6.0 V battery in series with a 1.5 V cell, both facing the same way, gives 7.5 V.
Worth remembering
- Series: one loop, components end to end. Parallel: each component in its own branch across the supply.
- Before switching on, check for a complete path from one terminal of the source back to the other.
- Sources in series facing the same way add their e.m.f.s; a reversed one subtracts.
Worked example
Two series resistors of 2 Ω and 4 Ω on 12 V carry 2 A; their potential differences are 4 V and 8 V.
Build a circuit
Free for everyone, on its own page.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
Total resistance = 6 Ω; current = 1 A; each resistor has 3 V.
Check your method, units and explanation against it.
Marked practice
Set 1 of 5 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.