Electric Circuits · Cambridge syllabus 4.3 · Lesson 5 of 5
Potential Dividers
Includes Supplement objectivesA potential divider uses two series resistances and takes an output across one. The p.d.s are in the ratio of the resistances, R₁/R₂ = V₁/V₂, so for an unloaded divider Vout = Vin × R₂/(R₁ + R₂). Replacing a resistor with a sensor makes output depend on temperature or light.
By the end, you can
- Know that, for a constant current, the potential difference across a conductor increases as its resistance increases.
- Recall and use R₁ ÷ R₂ = V₁ ÷ V₂ for two resistors used as a potential divider. [Supplement]
- Use LDRs and thermistors in potential-divider systems. [Supplement]
- Explain how environmental changes alter output voltage. [Supplement]
Potential divider
The same current passes through every component in series, and for a constant current the potential difference across a conductor increases as its resistance increases. So when two resistors are in series, the one with the larger resistance has the larger p.d. across it. That is the idea behind a potential divider: two resistors in series across a supply, splitting its p.d. into two parts, with the output taken across one of them.
The p.d.s are in the same ratio as the resistances: R₁ ÷ R₂ = V₁ ÷ V₂, where V₁ is the p.d. across R₁ and V₂ the p.d. across R₂. With a 9.0 V supply, a 1.0 kΩ and a 2.0 kΩ resistor, R₁ ÷ R₂ = 1 ÷ 2, so V₂ is twice V₁; as the two must add up to 9.0 V, V₁ = 3.0 V and V₂ = 6.0 V. Or, given a 4.0 kΩ resistor with 3.0 V across it in series with an unknown resistor with 9.0 V across it, the unknown is 4.0 × 9.0 ÷ 3.0 = 12 kΩ.
The same result can be written for the output directly: output p.d. = supply p.d. × R₂ ÷ (R₁ + R₂), taking the output across R₂. For the example above, 9.0 × 2.0 ÷ 3.0 = 6.0 V.
Replacing one fixed resistor with a variable resistor, or using a single resistor with a sliding contact, gives an output that can be adjusted smoothly from zero up to the full supply p.d., which is how a volume control or a dimmer works.
- R₁ ÷ R₂ = V₁ ÷ V₂
- In a potential divider the p.d.s are in the same ratio as the resistances.V₁ is the p.d. across R₁ and V₂ the p.d. across R₂.
- Vₒᵤₜ = Vᵢₙ × R₂ ÷ (R₁ + R₂)
- The output p.d. is the fraction of the supply p.d. taken by the resistor it is measured across.The output is taken across R₂.
Worth remembering
- For a constant current, a larger resistance has a larger p.d. across it.
- R₁ ÷ R₂ = V₁ ÷ V₂ for two resistors used as a potential divider.
- A variable resistor or sliding contact gives an adjustable output.
Sensor circuits
Put a sensor in one half of a potential divider and the output voltage changes with the surroundings, which is what makes an automatic circuit possible.
With an LDR in the divider, darkness raises its resistance, so it takes a larger share of the voltage. Wire the output across the LDR and the output voltage rises in the dark, which can switch on a lamp. Wire it across the fixed resistor instead and the output rises in the light. Which way round the two components go decides whether the circuit responds to dark or to light, and questions test exactly that.
A thermistor works the same way for temperature. Since its resistance falls as it warms, its share of the voltage falls as it warms, and the output taken across the other resistor rises — which can trigger a fan or a fire alarm.
The output usually feeds another part of the circuit, such as a relay coil, so that when the output p.d. becomes large enough the relay switches on a lamp, a heater or an alarm in a separate circuit.
Worth remembering
- A sensor in a divider turns a change in conditions into a change in voltage.
- Swapping which component the output is taken across reverses the response.
Worked example
With Vin = 12 V, R₁ = 2 kΩ and R₂ = 4 kΩ, Vout = 8 V across R₂.
Build a circuit
Free for everyone, on its own page.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
Vout = 10 × 1/2 = 5 V.
Check your method, units and explanation against it.
Marked practice
Set 1 of 5 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.