General Wave Properties · Cambridge syllabus 3.1 · Lesson 4 of 4
Reflection, Refraction and Diffraction
Includes Supplement objectivesReflection returns waves from a boundary. Refraction changes speed and usually direction when entering another medium; frequency remains fixed. Diffraction is spreading at gaps and edges, strongest when gap width is comparable to wavelength. A ripple tank shows all three: a plane barrier, a shallow region and a gap or edge.
By the end, you can
- Describe reflection of waves.
- Apply reflection to wavefront diagrams.
- Explain changes in wave direction and speed.
- Relate refraction to changes in medium.
- Explain spreading through gaps and around obstacles.
- Describe how wavelength and gap size affect diffraction through a gap, and how wavelength affects diffraction at an edge. [Supplement]
- Describe how a ripple tank shows reflection at a plane surface, refraction caused by a change in depth, and diffraction through a gap and at an edge.
Reflection
When a wave meets a barrier it can bounce off, and the rule is simple: the angle of incidence equals the angle of reflection. Both angles are measured from the normal, the line drawn perpendicular to the surface at the point where the wave strikes — not from the surface itself, which is the commonest error in this whole topic.
Reflection changes the direction of the wave but not its speed, frequency or wavelength, because the wave stays in the same medium throughout. That gives the rule for a wavefront diagram: draw the reflected wavefronts with the same spacing as the incoming ones, leaving the barrier at the same angle as the incoming wavefronts arrived, but turned the other way.
Straight water waves whose wavefronts meet a barrier at 30° to its surface leave it at 30° on the other side, and the gap between neighbouring wavefronts is unchanged. The same rule governs an echo, a mirror image and a radar return.
Worth remembering
- Angle of incidence = angle of reflection, both measured from the normal.
- Reflection changes direction only: speed, frequency and wavelength are unchanged.
- In a wavefront diagram, reflected wavefronts keep the same spacing and leave at the same angle.
Refraction
Refraction is the change in direction that happens when a wave crosses into a material where its speed is different. The frequency stays the same, so the wavelength changes along with the speed, and if the wave meets the boundary at an angle the whole wavefront pivots.
The direction of the bend follows one rule. Going into a slower medium, the wave bends towards the normal; going into a faster one, it bends away from the normal. Light entering glass from air slows and bends towards the normal; leaving glass into air it speeds up and bends away.
A wave meeting the boundary head-on, along the normal, does not change direction at all — its speed and wavelength still change, but there is no angle to pivot about. Water waves slow down in shallower water, which is why waves swing round to run almost parallel to a beach.
Worth remembering
- Refraction: a change of speed at a boundary causes a change of direction.
- Into a slower medium, bends towards the normal; into a faster one, away from it.
- Along the normal, there is no change of direction.
Diffraction
Diffraction is the spreading of a wave as it passes through a gap or around the edge of an obstacle. It happens to all waves, and it is why you can hear someone talking round a corner even though you cannot see them.
How much the wave spreads depends on the width of the gap compared with the wavelength. A gap many wavelengths wide lets the wave through with only slight spreading at the edges. Narrow the gap and the spreading increases; it is greatest when the gap is about the same size as the wavelength, when the wave fans out in a near-semicircle beyond it. Keep the gap fixed and lengthen the wavelength instead, and the effect is the same: more spreading. Diffraction changes the direction the wave travels, but not its wavelength, frequency or speed.
Diffraction also happens at a single edge, such as the end of a harbour wall. Beyond the edge the wave bends round into the region behind the obstacle, and the longer the wavelength, the further round it bends.
That comparison explains hearing round corners. Sound has wavelengths of roughly a metre, comparable to a doorway, so it diffracts strongly and reaches you. Visible light has wavelengths of less than a millionth of a metre, so a doorway is enormous by comparison and the light barely spreads at all. Long-wavelength radio waves diffract over hills; shorter-wavelength television signals do not, which is why reception in a valley can be poor.
Worth remembering
- Diffraction is the spreading of a wave through a gap or past an edge.
- Narrower gap or longer wavelength: more spreading. Greatest when the gap is about one wavelength.
- At an edge, a longer wavelength bends further round into the region behind.
- Diffraction does not change the wavelength, frequency or speed.
The ripple tank
A ripple tank is a shallow, glass-bottomed tray of water with a lamp above it. A bar driven by a small motor dips in and out of the water and sends straight waves across the tank, and the motor speed sets their frequency. Each crest acts like a weak lens and focuses the light, so the wavefronts show up as bright lines on a sheet of paper or a screen underneath, where they can be watched and measured. Sloping foam at the edges absorbs the waves so they do not reflect back and confuse the pattern.
To show reflection, stand a straight strip of metal or plastic in the water as a plane barrier, at an angle to the waves. The reflected wavefronts leave at the same angle as the incoming ones arrived, with the same spacing. To show refraction, lay a sheet of glass or perspex on the bottom of part of the tank so that the water above it is shallower. Water waves travel more slowly in shallow water, so over the sheet the wavefronts crowd closer together, showing a shorter wavelength, and if they meet the edge of the sheet at an angle they change direction.
To show diffraction through a gap, place two barriers in a line with a gap between them. Beyond the gap the straight wavefronts become curved and spread out, and making the gap narrower makes them spread more. To show diffraction at an edge, use a single barrier so that the waves pass its end. Beyond the edge the wavefronts curve round into the region behind the barrier, which would otherwise be still water.
Worth remembering
- A ripple tank shows wavefronts as bright lines on a screen below the tank.
- Plane barrier: reflection. Shallower water over a glass sheet: slower waves, shorter wavelength, refraction.
- A gap between two barriers, or the end of a single barrier: diffraction.
Worked example
If speed halves at a boundary while frequency stays fixed, wavelength halves.
Waves through a gap
Part of the full Physics course. This unit’s free simulation is Make a wave.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
The gap size becomes more comparable to the wavelength, giving greater spreading.
Check your method, units and explanation against it.
Marked practice
Set 1 of 5 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.