General Wave Properties · Cambridge syllabus 3.1 · Lesson 2 of 4
Wave Quantities
Includes Supplement objectivesAmplitude is maximum displacement from the rest position; wavelength is the distance between matching points on neighbouring waves. Frequency is the number of complete waves passing a point each second, measured in hertz: 1 Hz is one wave per second. Wave speed v = fλ.
By the end, you can
- Define amplitude.
- Define wavelength.
- Define frequency.
- Use the unit of frequency, the hertz (Hz), where 1 Hz is one wave per second.
- Use wave speed = frequency × wavelength.
- Rearrange the equation for frequency or wavelength.
- Use wave speed = frequency × wavelength with wavelengths in nanometres (nm) and frequencies in gigahertz (GHz). [Supplement]
Amplitude and wavelength
Amplitude is the maximum displacement of a particle from its undisturbed position — the height of a crest, or peak, above the rest position, or the depth of a trough below it. It is not the distance from crest to trough, which is twice the amplitude and a standard trap.
Amplitude determines how much energy the wave carries. A louder sound has a larger amplitude; a brighter light has a larger amplitude. A wave loses amplitude as it spreads out, which is why sound fades with distance.
Wavelength, written λ, is the distance between two corresponding points on neighbouring waves — crest to next crest, or trough to next trough. Measure it over several complete waves and divide, for the same reason you time twenty pendulum swings rather than one: if ten waves span 45 cm, the wavelength is 4.5 cm.
Worth remembering
- Amplitude = maximum displacement from the rest position, not crest to trough.
- Wavelength λ = distance between corresponding points on neighbouring waves.
- Larger amplitude means more energy carried.
Frequency
Frequency, f, is the number of complete waves passing a point each second. Its unit is the hertz, Hz, and one hertz means one wave per second. A wave of frequency 50 Hz sends 50 complete waves past each point every second; a frequency of 2 kHz means 2000 waves each second.
To find a frequency, count the waves and divide by the time. If 600 waves pass a point in 2.0 minutes, that is 600 waves in 120 s, so the frequency is 600 ÷ 120 = 5.0 Hz. Always change the time into seconds first, since a hertz is one wave per second, not per minute.
Frequency is set by the source: whatever is vibrating decides it, and the wave keeps that frequency even when it moves into a different material. A loudspeaker cone that moves back and forth 300 times each second makes a sound of 300 Hz. For sound, a higher frequency is heard as a higher pitch; for light, frequency is what we perceive as colour.
- frequency = number of waves ÷ time taken
- Frequency is the number of complete waves passing a point in each second.frequency in Hz, time in s
Worth remembering
- Frequency f = number of complete waves passing a point each second.
- Unit: the hertz, Hz. 1 Hz = one wave per second; 1 kHz = 1000 Hz.
- Frequency is fixed by the source and does not change when the wave enters a new material.
Wave speed
The wave equation ties the three together: v = fλ, wave speed equals frequency times wavelength. It follows directly from the definitions — f waves pass each second, each one λ long, so fλ metres of wave pass each second.
A sound of frequency 340 Hz in air, where the speed is about 340 m/s, therefore has a wavelength of 1 m. Radio waves travel at 3.0 × 10⁸ m/s, so a radio wave of frequency 100 MHz has a wavelength of 3.0 × 10⁸ ÷ 100 000 000 = 3 m.
The wavelength of light is usually given in nanometres and the frequency of microwaves in gigahertz. Replace the prefix by its power of ten before substituting: 1 nm = 10⁻⁹ m and 1 GHz = 10⁹ Hz. Orange light of wavelength 600 nm, travelling at 3.0 × 10⁸ m/s, has a frequency of 3.0 × 10⁸ ÷ (600 × 10⁻⁹) = 5.0 × 10¹⁴ Hz. A microwave signal of 5.0 GHz has a wavelength of 3.0 × 10⁸ ÷ (5.0 × 10⁹) = 0.060 m, or 6.0 cm.
The useful consequence appears when a wave enters a new material. The speed changes, but the frequency cannot, because it is set by the source. So the wavelength must change to keep v = fλ true. Light entering glass slows down and its wavelength shortens; its frequency, and so its colour, stays the same. That single fact is the whole explanation of refraction.
- v = fλ
- Wave speed is frequency times wavelength.v in m/s, f in Hz, λ in m
Worth remembering
- v = fλ, so f = v ÷ λ and λ = v ÷ f.
- Entering a new medium changes speed and wavelength; frequency is unchanged.
- Sound in air: about 340 m/s.
- Convert prefixes first: 1 nm = 10⁻⁹ m and 1 GHz = 10⁹ Hz.
Worked example
A wave with frequency 4 Hz and wavelength 0.5 m has speed 4 × 0.5 = 2 m/s.
Make a wave
Change a value and watch the readings follow. Open it on the lab stage
Make a wave
A wave travels along the light rope at 2 m/s, with its crests 2 m apart.
- Wave speed
- 2 m/s
- Wavelength
- 2 m
- 2 m/s ÷ 1 Hz
- Period
- 1 s
- 1 ÷ 1 Hz
- Crest-to-trough height
- 1 m
- 2 × 0.5 m
Goal
Find out what sets the speed of a wave along a rope, and what changing the frequency does to its wavelength.
Predict, where you are
If Ithe, thewill
Say what you expect before you move anything. Check makes the change for you.
Test, still to come
Change one thing at a time and watch the readings. Play the run to see it happen. The notebook keeps a reading each time you record one.
Explain, still to come
After you check a prediction, this says why it happened.
Try this · 0 of 2
- Follow the marked particle while a crest passes it. Does the particle travel along the rope with the wave?
- Raise the frequency on the light rope from 1 Hz to 2 Hz. What happens to the wavelength, and to the wave speed?, not yet
- Give a wave on the heavy rope a wavelength of 0.5 m., not yet
Source
v = fλ
2 m/s = 1 Hz × 2 m
Particle displacement / m
Investigation notebook · 0 readings
Change one variable at a time and record the results. These readings stay here until you leave this lesson or reset the notebook.
About this model
An ideal transverse wave on a rope long enough that nothing reflects from its far end, with no losses, so the amplitude never decays along it. Both ropes are under the same tension.
Practice
Warm-up · not marked
Check your understanding
Answer in your own words, then compare with the worked answer. Nothing here is saved or scored.
Worked answer
λ = v/f = 12/3 = 4 m.
Check your method, units and explanation against it.
Marked practice
Set 1 of 4 · easiest first · Checked as you go, with the worked answer. Sign in or create a free account to save your progress.